Het laatste nieuws van het bedrijf over How to Weld Galvanized Steel Plates for Storage Tanks and Liquid Containers

November 17, 2026

How to Weld Galvanized Steel Plates for Storage Tanks and Liquid Containers

Nieuwsdetails

How to Weld Galvanized Steel Plates for Storage Tanks and Containers

By the Yuhong Group technical team

Overview

In the fabrication of industrial storage tanks, agricultural storage bins, and liquid containers, galvanized steel plates are the preferred material due to their exceptional corrosion resistance and cost-efficiency. However, the very zinc coating that protects the container from rust creates significant challenges during the welding process. Fabricators frequently struggle with weld failures that can compromise the seal and lead to leaks.

At Yuhong Group, we supply high-quality galvanized steel plates and structural steel pipes specifically engineered for tank and container manufacturing. This article outlines the critical welding challenges in storage tank fabrication and the proven methods to solve them.

The Challenges: Why Welding Galvanized Tanks is Difficult

When constructing a storage tank or box, the weld seam must be perfectly sealed. However, the zinc coating (melting point ~419°C) vaporizes long before the steel (melting point ~1500°C) melts.

  • Cracks and Leaks: Molten zinc penetrates steel grain boundaries, forming brittle intermetallic compounds. Under the welding stress of a large tank shell, this leads to cracking, which is a catastrophic failure for any liquid storage container.
  • Porosity and Pinholes: Vaporized zinc (ZnO) gets trapped in the weld pool, creating porosity. Pinholes in a storage tank weld will inevitably lead to leakage over time. Higher welding currents worsen this porosity.
  • Toxic Fumes: Welding galvanized tanks generates significant ZnO dust. When fabricating enclosed storage bins, confined space ventilation is critical for worker safety.
  • Oxide Slag: Stable ZnO slag can reduce the plasticity of the weld joint, making the tank susceptible to structural failure under load.

Solutions for Storage Tank Fabrication

To ensure a leak-proof storage tank or box, pre-weld preparation is mandatory:

  • Groove Preparation: Open V, Y, or X-shaped grooves. Use oxygen-acetylene or sandblasting to remove the zinc coating near the weld seam.
  • Gap Control: Keep the root gap around 1.5 mm (or 2.5~3 mm for thicker tank shells).
  • Material Selection: Use low-silicon (Si < 0.2%) welding wires and electrodes. Yuhong Group provides base plates with consistent thickness tolerances, ensuring precise gap control during assembly.

1. Shielded Metal Arc Welding (SMAW) for Containers

SMAW is highly effective for on-site repairs or fabricating smaller storage boxes. It generates less dust than gas welding.

Electrode Selection:

  • Low carbon galvanized plates: J421 / J422 or J423.
  • High-strength tank shells (>500 MPa): E5001, E5003.
  • Heavy-duty tanks (>600 MPa): E6013, E5503, E5513.

Technique: Use a short arc without oscillating the electrode to protect the zinc layer and minimize fume generation.

2. Gas Metal Arc Welding (GMAW) for Large Tanks

For large-scale tank shells, GMAW (CO2, Ar+CO2, or Ar+O2) offers much higher efficiency. Pure CO2 yields a higher Zn content in the weld, while Ar+CO2 mixtures reduce it.

  • Ventilation: GMAW generates more dust. Good exhaust systems are essential, especially inside storage bins.
  • Penetration: GMAW achieves deeper penetration on galvanized plates, but higher welding speeds increase porosity sensitivity, particularly for T-joints on tank flanges.

Recommended CO2 Welding Parameters for Galvanized Plate Fabrication

Using ER70S-3 wire, diameter 0.9 mm, dry extension 6.4 mm.

Table 1: Butt Joint (Tank Shell) CO2 Welding Parameters

Thickness (mm) Gap (mm) Welding Position Wire Feed Speed (mm/s) Arc Voltage (V) Welding Current (A) Welding Speed (mm/s)
1.6 0 Flat 59.2~80.4 17~20 70~90 5.1~7.2
3.2 0.8~1.5 Flat 71.9 20 135 5.5

Table 2: Lap Joint (Container Flanges) CO2 Welding Parameters

Thickness (mm) Welding Position Wire Feed Speed (mm/s) Arc Voltage (V) Welding Current (A) Welding Speed (mm/s)
1.6 Flat 50.8 19 110 5.1~6.8
3.2 Flat 67.2 19 135 3.8~4.2

Yuhong Group Supply & CTA

Achieving high-quality welds starts with the right material. At Yuhong Group, we specialize in supplying premium galvanized steel plates, seamless pipes, and structural profiles tailored for the storage tank and container industry. We offer flexible MOQ (1 Ton), competitive FOB pricing, and a reliable Lead Time (15-25 days) to keep your fabrication schedule on track. Contact our technical team today to discuss your tank manufacturing requirements and get a fast quotation.

Frequently Asked Questions

Can galvanized steel plates be used for liquid storage tanks?

Yes, galvanized steel is highly corrosion-resistant. However, the zinc coating must be carefully removed at the weld seams to prevent porosity, which could lead to leaks in the storage tank.

How do you prevent welding cracks in galvanized storage boxes?

Prevent cracks by opening proper grooves, removing the zinc layer via sandblasting, keeping the gap around 1.5 mm, and selecting low-silicon (Si) welding materials.

What is the best welding method for large galvanized tanks?

GMAW (CO2 gas shielded welding) is generally more efficient for large tank shells due to its higher deposition rate. SMAW is better for smaller bins and on-site repairs because it produces less dust.

Why is ventilation important when welding galvanized containers?

The zinc coating evaporates into harmful ZnO dust during welding. In enclosed spaces like storage bins, proper ventilation is mandatory to protect workers' respiratory systems.

Author: Yuhong Group Technical Team — welding & fabrication specialists for galvanized steel plates, seamless pipes and structural profiles used in storage tanks, silos and liquid containers.

Reviewed by the Yuhong Group engineering department. For technical consultation and quotations, contact our sales team.

Welded galvanized steel liquid container used for storage.